ROLF SCHLICHT GmbH

ROLF SCHLICHT GmbH offers a wide range of system solutions for multifunctional cutting tasks. Wherever we do not cut, we offer a comprehensive range of semi or fully automatic winders with strapping, setting, shrinking and ejection respectively depositing systems on pallets or conveyor belts.

The field of application for our systems is the production area of plastic and rubber extrusion for the production of hoses, tubes, profiles, strips from smallest diameters up to less than 1 mm in medical technology up to tubes of approx. 100 mm diameter.

We supply our feeding and cutting systems also in GMP version for the pharmaceutical industry and medical technology for the clean room. The systems work in the extrusion line or outside the line from the coil, the winding belt or out of the pallet.

 We adapt the systems to your wishes and needs in order to achieve the best possible effectiveness for you.

• Trimming
• Cutting
• Cutting-off
• Pull-off
• Transport with or without pull
• Line independent operation by loop-control
• Discharge
• Blow-off or ejection
• Collection and sorting in pans, cartons, boxes or bags

We offer you the opportunity, based on many years of experience and product knowledge, to develop a system solution tailored to your requirements. Planning, production, service and spare parts supply - all from one source.

The team of ROLF SCHLICHT GmbH is looking forward to your visit and interesting discussions on our stand A35 in hall 3.

Of course you can inform yourself in advance about our manifold product range on our homepage www.schlicht-gmbh.de or by e-mail to info@schlicht-gmbh.de .

Since week 11/2019 ROLF SCHLICHT GmbH supplies the new machine generation RS POWDERTECH „RSC-NG“ (ROLF SCHLICHT COATING-NEXT GENERATION).

 The machine structure is similar to the previous model. For the RSC-NG, however, both a new electrostatic has been completely redeveloped, as well as a new filter system. We also made some minor changes that improve safety and handling.

The new e-static system is state-of-the-art in surface coating technology and shows a reduction in wear parts in the gun and cascade. The completely redesigned cascade and pistols improve the powder result.

Compared to all predecessor generations, the new system shows significantly less power loss due to the design and offers full performance even when operating with two up to four guns. In the old generation, the performance was split at two pistols.

With an additional switch, the e-statics can be completely switched off while the machine is running. A flashlight indicates whether there is still charge. The settings are made as a target/actual values.

The guns are made of stronger material and much more stable than the previous models. The possibility of electric shock due to incorrect installation of the pistols after maintenance has been significantly reduced.

Optionally, an automatic cleaning can be built into the gun, which reduces the wear of the gun. This is operated automatically by means of a program from the control unit.

The new filter system shows better cleaning results and has been designed to provide both longer filter life and easier, faster and cheaper maintenance. Spare parts costs are reduced. The new system operates simpler. This allows the integration of simple parts with less susceptibility to wear and failure.

Some more, minor changes were carried out to prepare the machine for further innovations and to improve the production processes.

We provide conversion packages for the new electrostatics and the new filter system, which will make it possible to equip the old RSC version with these two new components.

This will not be the last innovations we have set for the future. Our aim is to incorporate feedback from the customer into the optimization of the machines more quickly. We will continue to stick to the tried and tested in the future, but we are also open to suggestions that we will gladly incorporate into our products after testing.

The team of ROLF SCHLICHT GmbH is looking forward to your visit and interesting discussions on our stand A35 in hall 3.

Of course you can inform yourself in advance about our manifold product range on our homepage www.schlicht-gmbh.de or by e-mail to info@schlicht-gmbh.de .
 

SAGITTA band granulators have been used in different production processes by the most important industries for more than 60 years.

 SAGITTA Band granulator
The SAGITTA band granulator is a machine for granulating rubber compounds of all kinds based on natural and synthetic rubber as well as for granulating thermoplastics, such as hard or soft PVC, HDPE, LDPE, polyamide, ABS, PE etc.

 The machines are also used for granulating linoleum, molding compounds and pulp, as well as sponge rubber, silicone and pure natural rubber.

The feeding of extruders and injection molding presses with granules instead of strips offers various advantages such as blending of different compounds and thus better quality, less pulsation in the screw, lower power consumption of the motor, automatic feeding of extruders and injection molding presses.

Many manufacturers of solvent use SAGITTA band granulators because granules of i.e. 5x5x5 mm can reduce the dissolving times significantly.
There are machines available with and without automatic powdering unit. The granulation output range is from 150 to 12,000 kg / hour.

Machines with working widths of 130-1200 mm are supplied for granule sizes of
3x3 mm, 5x5 mm, 8x8 mm, 10x10 mm and 15x15 mm.

For very hard and smooth belts, the feeding cylinders are delivered in toothed execution to prevent slippage. For granulating very abrasive compounds, carbide knives are available.

 The other product range includes pneumatic transport and pulverization systems for rubber granules as well as powder feeders for the granulators.

SAGITTA horizontal splitter for elastomers - RSP 55 SX
RSP 55 SX splits elastomers with a maximum width of 550 mm and maximum thickness of 60 mm up to a minimum thickness of 0.2 mm.

 Main features:
- Automatic sharpening of the band knife.
- Automatic positioning and compensation of knife consumption.
- Special equipment for knife lubrication.
- High precision knife guide plate with automatic adjustment.
- Upper transport roller and adjustment of the roller pressure lower roller.
- Electronic adjustment of the feed rate and the upper and lower cutting thickness.

Our distribution partner NorMec will show the film vulcanizing splicing press, type 110-00-150 at the K 2019.
This press is the evolution of the reliable standard press 101-00-80 that NorMec build for more than 30 years.

All safety features of the standard machine comply with the European Code of safety EN 201. Electrical connection 230 VAC 50/60 Hz, compressed air 6 bar.

The new model has several new and smart solutions and improved construction to handle tools up to 150 mm.

The user can easily set-up all settings on the machine directly in the interface. One of the new features is password protection of the machine and new help function for the operator and maintenance personnel.

If any problems should occur, troubleshooting can be done easily and directly on the control panel.

The newest optional feature is installation of VPN (Virtual Private Network). With the VPN our technical engineers can connect directly too your machine for troubleshooting or upgrading of software.

The press is prepared for/ to operate a semi-automatic film dispenser. It is possible to splice rings with diameters as small as 225 mm.

All of NorMec splicing presses are equipped with the ”gap”-program. The ”gap”-program involves closing the tools in the press with two-hands buttons and once released again the tool opens approximately 2 mm and the operator has both hands free to insert the profiles into the tool. After this is done the profiles are locked in the tool by pushing the foot-pedal.

All NorMec splicing presses has functions that give the operator opportunity to close one and one side off the tools. This allows the operator to use both hands to hold multiple profiles when he wants to splice for instance 6 profiles in the same operation.

It is also possible to close the moulds and lock the profiles in the tool in the outer position, this make it possible to cut the profile directly in the tool. This makes it easy to achieve good angle splices when dealing with difficult profiles.

Visit us at K 2019 in Duesseldorf 16 – 23 October in hall 3 – stand A35.

Huestis Industrial air wipes are used in the cable, wire and hose industry. They are quiet, highly efficient and make a profit on their investment within a short time, because the compressed air consumption is very low due to a special nozzle design.

The air misers are offered from 3 mm diameter up to 178 mm diameter. Special sizes and rectangular nozzles are available.
For the passage of knots, thickenings, splicing, etc., the nozzles open independently, so that damage is avoided.

Due to the small size, they can easily be mounted in any cooling section. The nozzles are mounted in stainless steel holders with snap fasteners. The compressed air connection is provided with a quick coupling.

HUESTIS Cable stripper
Huestis Industrial cable strippers are devices for stripping or skinning cables and wires with core or conductor diameters from 0.8 to 100 mm. In many cases, just the recovery of one drum is enough is paying for the machine.

How it works
A hardened steel stripper foot sized closely to the core diameter separates the jacket from the core. The steel saw blade rides in a closed groove in the foot. Only the protective foot has contact with the core and makes a damage of it impossible.

Furthermore a combined puller-chopper (JPC) for the cut jacket is available. This cuts the jacket to pieces of abt. 200 to 300 mm length.

Advantages
·         No damaging of the core
·         Stripping in the coiling stand
·         Cable guiding by stripper foot
·         Centering by roll guides
·         Two cut heads possible
·         Puller-chopper
·         Up to 75 m/min.

BATTAGGION
The company Battaggion was founded in 1918 and works to the latest technical standards. The company has already delivered many systems to the German and Austrian market.

From the planning of the project to the final assembly and installation of the individual machine or the entire system, tailor-made solutions are offered for Sigma and Z-kneaders, granulation systems, turbo mixers, high-speed mixers, vacuum dryers, planetary mixers and twin-screw extruders, rolling mills, extruders for silicone processing.
 

ENRICO MOLTENI
the company is specialized in the production of machines for liquid and pasty products, which are characterized by low to high viscosity. Each project is individually developed and manufactured according to the specific requirements of the customer.

The mixing technology is offered for the chemical, food, pharmaceutical, cosmetic, rubber and plastics industries.

Application in the chemical industry in the field of:
- rubber, silicone
- plastic
- friction materials
- PVC
- foods
- adhesives
- pharmaceuticals
- chemicals etc.

In addition, various systems for feeding, transporting and emptying are supplied with state-of-the-art dosing and weighing systems as well as special applications.

The company is a subsidiary of the Battaggion group.

 
VALTORTA
The company is specialist for the production of mixing plants for powders and granules, liquids or mushy products. It offers turbo mixers, high-speed mixers, vacuum dryers, mixer lines, kneaders and planetary mixers, which are developed and manufactured according to customer requirements.

Valtorta is a subsidiary of the Battaggion group.

For more information ROLF SCHLICHT GmbH as representative of Battaggion group is expecting you in hall 3 / A35 or visit Battaggion directly in hall 9 / D05.

The FRIUL FILIERE GROUP was established in 1978 and manufactures machines and tools especially for the production of thermoplastic materials on an international level. FRIUL FILIERE is currently the only Italian company that produces complete extrusion equipment and tools in-house. The wide range of production of the company includes among others:

Complete systems for the production of window profiles, gaskets, panels, pipes, waterstop profiles, cable duct profiles and other profiles for the electronics, edgeband profiles, picture frame profiles, roller shutter profiles, "plinth" profiles, sealing profiles in soft PVC and other thermoplastic materials (also with metal profiles), as well as extrusion lines for the production of customized applications.

The production program also includes single-screw extruders, twin-screw extruders (conical and parallel), co-extruders and complete downstream units. FRIUL FILIERE supplies complete systems together with know-how and recipe.

This year, FRIUL FILIERE will present a new generation of single-screw and twin-screw extruders.

These systems are of interest to customers who want to implement and manage very ambitious projects and are looking for a suitable system to achieve the best possible level of production.

With nearly 30 years of experience, the company can offer competitive standard solutions as well as customized solutions in the field of profile and pipe extrusion.

Visit ROLF SCHLICHT GmbH as representative of FRIUL FILIERE in hall 3 / A35.

You  will find FRIUL FILIERE with own stand in hall 16 / D72.

Bale cutter type PumaCut
The machines type PumaCut are automatic, hydraulic bale cutting machines of the company PumaTech, Italy. The machines are particularly suitable for cutting rubber bales in any length, cutting range and cutting height depending on the model.

 
Deflashing machine type PumaJet
This shot-blasting deflashing machine is particularly suitable for deflashing small parts made of rubber, silicone or similar materials.

The machine is equipped with a rotating drum made of perforated stainless steel. The variable speed drum is mounted by a linear guide. A variable speed turbine injects the abrasive into the interior of the drum. The return transport of the blasting medium takes place by means of a spiral conveyor with variable speed.

The parts are cooled by injecting liquid nitrogen, regulated by a valve. At the end of the cycle, the deflashed parts are unloaded from the drum onto a vibrating screen to separate the parts from the burr. Loading capacity of the drum 6 - 8 l. Operation via PC and inverter.

For more information visit us at K 2019 in Duesseldorf 16 – 23 October in hall 3, stand A35.

Alpha DisperGRADER ™ αview uses state-of-the-art technology to radically extend the capabilities of optical dispersion analysis techniques. Using a reflected light microscope designed for dispersion testing of carbon black in mixed rubber compounds, the system analyzes the shadows cast by agglomerates present in a freshly cut sample surface.

The device has an autofocus for fast and consistent analysis and captures multiple data points per sample placement.

The machine equipment includes automatic and manual scanning functions, histogram, analysis data and image database, 5 pre-installed and user-defined image databases and a color camera.

The image analysis software determines the size, number and position of agglomerates.

Available are the DisperGRADER ™ αview SR model (3-57 micron) and / or the DisperGRADER ™ αview HR model (1-20 micron) as well as an optional uncured sample preparation system.