DuPont de Nemours International S.A.

Air duct for high performance engines, blow-molded in DuPont™ Hytrel®, reduces weight and cost

The lower duct section A, extrusion blow-molded from DuPont™
The lower duct section A, extrusion blow-molded from DuPont™ Hytrel®, consists of the flange with a fitted metal coupling as a connection to the intercooler, a welded bracket and the metal-ring-reinforced coupling to the upper duct section B, which is also made of Hytrel® and is located on the throttle body side. The integrated bellow in this duct counters any relative movement between the vehicle and engine and permits a degree of flexibility for assembly purposes. Following on from an additional screw-on clip, there is a connecting flange for the engine sound system, two couplings for wastegate (gray) and – just ahead of the connection flange on the throttle body side – a bracket with sensor.

Air duct for high performance engines, blow-molded in DuPont™ Hytrel®, reduces weight and cost

Geneva, March 17 2010 - A newly-developed two-component air duct, from system supplier MAHLE of Stuttgart, Germany, connects the intercooler and throttle body of the three liter, six cylinder twin-turbo engine from BMW. Blow-molded using stiff yet elastic DuPont™ Hytrel® HTR4275, the air duct fulfills its task in a particularly efficient manner due to the very low material usage of the design and despite the high pressures and flow velocity encountered in such a high-performance petrol engine. By reducing the part to just two basic components, the time required for production and assembly is significantly reduced compared to the previous version, which was used up until mid-2009, and consisted of a series of pipes and clamps. Moreover, blow-molding technology enables greater flexibility in the integration of application-specific connections, such as those required for resonators, sensors or the discharge of gases. Together, the combination of lower weight, more efficient production and assembly, and the integration of variable functionality, provides for a significant cost advantage over the earlier model, which was produced using glass-fiber reinforced nylon and elastomers.

Used on the ‘cold’ side of the engine, the innovative air duct, consisting of two Hytrel® sections measuring 300 mm and 400 mm respectively, is one of the first mono-material solutions of its kind in Germany. “Despite the ambitious nature of this development, we succeeded, with DuPont’s support, in combining high functionality with high cost-efficiency,” comments Thorsten Riechelmann, project manager at MAHLE. “For example, finite element calculations conducted by DuPont helped us to optimize wall thickness in line with the given pressure and temperature conditions (2 bar absolute pressure at -40 °C to +100 °C). The same simulations from DuPont also generated very precise assembly data. This enabled us, for example, to optimise the integrated bellows at a sufficiently early stage to ensure that the high levels of deformation, necessary due to the limited assembly space, and the pressure levels required to install it, were within an acceptable range.” Riechelmann continues: “Overall there was a strong correlation between the values provided by DuPont and those which resulted from actual component testing. We also appreciated greatly the technical support available from DuPont’s technical centre in Geneva with regard to three-dimensional blow molding. From there we were able to source valuable advice on how to conduct both energy-saving and reliable processing, which simplified the start of serial production considerably.”

Hytrel® thermoplastic polyester elastomers from DuPont provide the flexibility of rubbers, the strength of plastics, and the processibility of thermoplastics. Hytrel® HTR4275 is a specially-modified grade for use in blow-molding, with an increased melt viscosity, a hardness of 55 Shore D and a relatively high stiffness of 170 MPa at 23 °C and 60 MPa at 100 °C. Thus it combines good mechanical properties at high temperatures – a prerequisite for air ducts which are located under the hood and consistently exposed to internal pressure – with high elasticity across a broad temperature range. As with all Hytrel® grades, this blow-molding grade offers long-term resistance to hydrocarbons and other media typical for the automotive sector.

The MAHLE Group is amongst the 30 largest automotive suppliers and is the world’s leading producer of components and systems for the combustion engine and its peripherals. MAHLE employs around 45,000 people at over 100 production facilities and eight Research & Development centres in Stuttgart, Northampton, Detroit (Farmington Hills, Novi), Tokyo (Kawagoe, Okegawa), Shanghai and São Paulo (Jundiaí). In 2008, MAHLE achieved a turnover of over 5 bn. Euros (7.3 bn. USD).

The DuPont Performance Polymers business manufactures and sells Crastin® PBT and Rynite® PET thermoplastic polyester resins, Delrin® acetal resins, Hytrel® thermoplastic polyester elastomers, DuPont™ ETPV engineering thermoplastic vulcanizates, Minlon® mineral reinforced nylon resins, Neoprene polychloroprene, Thermx® PCT polycyclohexylene dimethyl terephthalate, Tynex® filaments, Vespel® parts and shapes, Zenite® LCP liquid crystal polymers, Kalrez® perfluoroelastomer parts, Vamac® ethylene acrylic elastomers (AEM), Viton® fluoroelastomers, Viton® FreeFlow™ processing aids, Zytel® nylon resins and Zytel® HTN high-performance polyamides. These products serve global markets in the aerospace, appliance, automotive, consumer, electrical, electronic, healthcare, industrial, sporting goods and many other diversified industries.

DuPont is a science-based products and services company. Founded in 1802, DuPont puts science to work by creating sustainable solutions essential to a better, safer, healthier life for people everywhere. Operating in more than 70 countries, DuPont offers a wide range of innovative products and services for markets including agriculture and food; building and construction; communications; and transportation.


The DuPont Oval logo, DuPont™, The miracles of science™ and all products denoted with ® ot ™ are registered trademarks or trademarks of E.I. du Pont de Nemours and Company or its affiliates.

Note to the editor:
This press release is based on information provided by:
MAHLE Filtersysteme GmbH, Pragstraße 54, D-70376 Stuttgart
Contact: Thorsten Riechelmann
Telephone: +49 (0) 7 11-5 01-20915